110 lines
3.3 KiB
Arduino
110 lines
3.3 KiB
Arduino
|
#include <WiFi.h>
|
||
|
|
#include <ESPmDNS.h>
|
||
|
|
#include <WiFiUdp.h>
|
||
|
|
#include <ArduinoOTA.h>
|
||
|
|
#include <TFT_eSPI.h>
|
||
|
|
|
||
|
|
#define PIN_POWER_ON 15
|
||
|
|
|
||
|
|
TFT_eSPI tft = TFT_eSPI();
|
||
|
|
|
||
|
|
const char *ssid = "LilyGo-AABB";
|
||
|
|
const char *password = "xinyuandianzi";
|
||
|
|
|
||
|
|
void drawProgressBar(uint16_t x0, uint16_t y0, uint16_t w, uint16_t h, uint8_t percentage, uint16_t frameColor, uint16_t barColor)
|
||
|
|
{
|
||
|
|
if (percentage == 0) {
|
||
|
|
tft.fillRoundRect(x0, y0, w, h, 3, TFT_BLACK);
|
||
|
|
}
|
||
|
|
uint8_t margin = 2;
|
||
|
|
uint16_t barHeight = h - 2 * margin;
|
||
|
|
uint16_t barWidth = w - 2 * margin;
|
||
|
|
tft.drawRoundRect(x0, y0, w, h, 3, frameColor);
|
||
|
|
tft.fillRect(x0 + margin, y0 + margin, barWidth * percentage / 100.0, barHeight, barColor);
|
||
|
|
}
|
||
|
|
|
||
|
|
void setup()
|
||
|
|
{
|
||
|
|
Serial.begin(115200);
|
||
|
|
Serial.println("Booting");
|
||
|
|
|
||
|
|
pinMode(PIN_POWER_ON, OUTPUT);
|
||
|
|
digitalWrite(PIN_POWER_ON, HIGH);
|
||
|
|
|
||
|
|
tft.init();
|
||
|
|
tft.setRotation(1);
|
||
|
|
tft.fillScreen(TFT_BLACK);
|
||
|
|
tft.setCursor(0, 0);
|
||
|
|
tft.println("OTA Start");
|
||
|
|
|
||
|
|
WiFi.mode(WIFI_STA);
|
||
|
|
WiFi.begin(ssid, password);
|
||
|
|
while (WiFi.waitForConnectResult() != WL_CONNECTED) {
|
||
|
|
Serial.println("Connection Failed! Rebooting...");
|
||
|
|
tft.println("Connection Failed! Rebooting...");
|
||
|
|
delay(5000);
|
||
|
|
ESP.restart();
|
||
|
|
}
|
||
|
|
|
||
|
|
// Port defaults to 3232
|
||
|
|
// ArduinoOTA.setPort(3232);
|
||
|
|
|
||
|
|
// Hostname defaults to esp3232-[MAC]
|
||
|
|
// ArduinoOTA.setHostname("myesp32");
|
||
|
|
|
||
|
|
// No authentication by default
|
||
|
|
// ArduinoOTA.setPassword("admin");
|
||
|
|
|
||
|
|
// Password can be set with it's md5 value as well
|
||
|
|
// MD5(admin) = 21232f297a57a5a743894a0e4a801fc3
|
||
|
|
// ArduinoOTA.setPasswordHash("21232f297a57a5a743894a0e4a801fc3");
|
||
|
|
|
||
|
|
ArduinoOTA
|
||
|
|
.onStart([]() {
|
||
|
|
String type;
|
||
|
|
if (ArduinoOTA.getCommand() == U_FLASH)
|
||
|
|
type = "sketch";
|
||
|
|
else // U_SPIFFS
|
||
|
|
type = "filesystem";
|
||
|
|
|
||
|
|
// NOTE: if updating SPIFFS this would be the place to unmount SPIFFS using SPIFFS.end()
|
||
|
|
Serial.println("Start updating " + type);
|
||
|
|
})
|
||
|
|
.onEnd([]() {
|
||
|
|
Serial.println("\nEnd");
|
||
|
|
})
|
||
|
|
.onProgress([](unsigned int progress, unsigned int total) {
|
||
|
|
Serial.printf("Progress: %u%%\r", (progress / (total / 100)));
|
||
|
|
int percentage = (progress / (total / 100));
|
||
|
|
tft.setTextDatum(TC_DATUM);
|
||
|
|
tft.setTextPadding(tft.textWidth(" 888% "));
|
||
|
|
tft.drawString(String(percentage) + "%", 145, 35);
|
||
|
|
drawProgressBar(10, 30, 120, 15, percentage, TFT_WHITE, TFT_BLUE);
|
||
|
|
})
|
||
|
|
.onError([](ota_error_t error) {
|
||
|
|
Serial.printf("Error[%u]: ", error);
|
||
|
|
if (error == OTA_AUTH_ERROR) Serial.println("Auth Failed");
|
||
|
|
else if (error == OTA_BEGIN_ERROR) Serial.println("Begin Failed");
|
||
|
|
else if (error == OTA_CONNECT_ERROR) Serial.println("Connect Failed");
|
||
|
|
else if (error == OTA_RECEIVE_ERROR) Serial.println("Receive Failed");
|
||
|
|
else if (error == OTA_END_ERROR) Serial.println("End Failed");
|
||
|
|
|
||
|
|
tft.fillScreen(TFT_BLACK);
|
||
|
|
tft.drawString("Update Failed", tft.width() / 2 - 20, 55 );
|
||
|
|
delay(3000);
|
||
|
|
tft.fillScreen(TFT_BLACK);
|
||
|
|
});
|
||
|
|
|
||
|
|
ArduinoOTA.begin();
|
||
|
|
|
||
|
|
tft.println("IP address: ");
|
||
|
|
tft.println(WiFi.localIP().toString());
|
||
|
|
Serial.println("Ready");
|
||
|
|
Serial.print("IP address: ");
|
||
|
|
Serial.println(WiFi.localIP());
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop()
|
||
|
|
{
|
||
|
|
ArduinoOTA.handle();
|
||
|
|
}
|