245 lines
7.6 KiB
C++
245 lines
7.6 KiB
C++
/*!
|
|
* @file Adafruit_MPR121.cpp
|
|
*
|
|
* @mainpage Adafruit MPR121 arduino driver
|
|
*
|
|
* @section intro_sec Introduction
|
|
*
|
|
* This is a library for the MPR121 I2C 12-chan Capacitive Sensor
|
|
*
|
|
* Designed specifically to work with the MPR121 sensor from Adafruit
|
|
* ----> https://www.adafruit.com/products/1982
|
|
*
|
|
* These sensors use I2C to communicate, 2+ pins are required to
|
|
* interface
|
|
*
|
|
* Adafruit invests time and resources providing this open source code,
|
|
* please support Adafruit and open-source hardware by purchasing
|
|
* products from Adafruit!
|
|
*
|
|
* @section author Author
|
|
*
|
|
* Written by Limor Fried/Ladyada for Adafruit Industries.
|
|
*
|
|
* @section license License
|
|
*
|
|
* BSD license, all text here must be included in any redistribution.
|
|
*/
|
|
|
|
#include "Adafruit_MPR121.h"
|
|
|
|
/*!
|
|
* @brief Default constructor
|
|
*/
|
|
Adafruit_MPR121::Adafruit_MPR121() {}
|
|
|
|
/*!
|
|
* @brief Begin an MPR121 object on a given I2C bus. This function resets
|
|
* the device and writes the default settings.
|
|
* @param i2caddr
|
|
* the i2c address the device can be found on. Defaults to 0x5A.
|
|
* @param *theWire
|
|
* Wire object
|
|
* @returns true on success, false otherwise
|
|
*/
|
|
boolean Adafruit_MPR121::begin(uint8_t i2caddr, TwoWire *theWire)
|
|
{
|
|
|
|
_i2caddr = i2caddr;
|
|
_wire = theWire;
|
|
|
|
// _wire->begin();
|
|
|
|
// soft reset
|
|
writeRegister(MPR121_SOFTRESET, 0x63);
|
|
delay(1);
|
|
for (uint8_t i = 0; i < 0x7F; i++) {
|
|
// Serial.print("$"); Serial.print(i, HEX);
|
|
// Serial.print(": 0x"); Serial.println(readRegister8(i));
|
|
}
|
|
|
|
writeRegister(MPR121_ECR, 0x0);
|
|
|
|
uint8_t c = readRegister8(MPR121_CONFIG2);
|
|
|
|
if (c != 0x24)
|
|
return false;
|
|
|
|
// setThreshholds(255, 255);
|
|
setThreshholds(12, 6);
|
|
writeRegister(MPR121_MHDR, 0x01);
|
|
writeRegister(MPR121_NHDR, 0x01);
|
|
writeRegister(MPR121_NCLR, 0x0E);
|
|
writeRegister(MPR121_FDLR, 0x00);
|
|
|
|
writeRegister(MPR121_MHDF, 0x01);
|
|
writeRegister(MPR121_NHDF, 0x05);
|
|
writeRegister(MPR121_NCLF, 0x01);
|
|
writeRegister(MPR121_FDLF, 0x00);
|
|
|
|
writeRegister(MPR121_NHDT, 0x00);
|
|
writeRegister(MPR121_NCLT, 0x00);
|
|
writeRegister(MPR121_FDLT, 0x00);
|
|
|
|
writeRegister(MPR121_DEBOUNCE, 0);
|
|
writeRegister(MPR121_CONFIG1, 0x10); // default, 16uA charge current
|
|
writeRegister(MPR121_CONFIG2, 0x20); // 0.5uS encoding, 1ms period
|
|
|
|
// writeRegister(MPR121_AUTOCONFIG0, 0x8F);
|
|
|
|
// writeRegister(MPR121_UPLIMIT, 150);
|
|
// writeRegister(MPR121_TARGETLIMIT, 100); // should be ~400 (100 shifted)
|
|
// writeRegister(MPR121_LOWLIMIT, 50);
|
|
// enable all electrodes
|
|
writeRegister(MPR121_ECR, 0x8F); // start with first 5 bits of baseline tracking
|
|
|
|
return true;
|
|
}
|
|
|
|
/*!
|
|
* @brief DEPRECATED. Use Adafruit_MPR121::setThresholds(uint8_t touch,
|
|
* uint8_t release) instead.
|
|
* @param touch
|
|
* see Adafruit_MPR121::setThresholds(uint8_t touch, uint8_t *release)
|
|
* @param release
|
|
* see Adafruit_MPR121::setThresholds(uint8_t touch, *uint8_t release)
|
|
*/
|
|
void Adafruit_MPR121::setThreshholds(uint8_t touch, uint8_t release)
|
|
{
|
|
setThresholds(touch, release);
|
|
}
|
|
|
|
/*!
|
|
* @brief Set the touch and release thresholds for all 13 channels on the
|
|
* device to the passed values. The threshold is defined as a
|
|
* deviation value from the baseline value, so it remains constant even baseline
|
|
* value changes. Typically the touch threshold is a little bigger than the
|
|
* release threshold to touch debounce and hysteresis. For typical touch
|
|
* application, the value can be in range 0x05~0x30 for example. The setting of
|
|
* the threshold is depended on the actual application. For the operation details
|
|
* and how to set the threshold refer to application note AN3892 and MPR121
|
|
* design guidelines.
|
|
* @param touch
|
|
* the touch threshold value from 0 to 255.
|
|
* @param release
|
|
* the release threshold from 0 to 255.
|
|
*/
|
|
void Adafruit_MPR121::setThresholds(uint8_t touch, uint8_t release)
|
|
{
|
|
// set all thresholds (the same)
|
|
for (uint8_t i = 0; i < 12; i++) {
|
|
writeRegister(MPR121_TOUCHTH_0 + 2 * i, touch);
|
|
writeRegister(MPR121_RELEASETH_0 + 2 * i, release);
|
|
}
|
|
}
|
|
|
|
/*!
|
|
* @brief Read the filtered data from channel t. The ADC raw data outputs
|
|
* run through 3 levels of digital filtering to filter out the high frequency and
|
|
* low frequency noise encountered. For detailed information on this filtering
|
|
* see page 6 of the device datasheet.
|
|
* @param t
|
|
* the channel to read
|
|
* @returns the filtered reading as a 10 bit unsigned value
|
|
*/
|
|
uint16_t Adafruit_MPR121::filteredData(uint8_t t)
|
|
{
|
|
if (t > 12)
|
|
return 0;
|
|
return readRegister16(MPR121_FILTDATA_0L + t * 2);
|
|
}
|
|
|
|
/*!
|
|
* @brief Read the baseline value for the channel. The 3rd level filtered
|
|
* result is internally 10bit but only high 8 bits are readable from registers
|
|
* 0x1E~0x2A as the baseline value output for each channel.
|
|
* @param t
|
|
* the channel to read.
|
|
* @returns the baseline data that was read
|
|
*/
|
|
uint16_t Adafruit_MPR121::baselineData(uint8_t t)
|
|
{
|
|
if (t > 12)
|
|
return 0;
|
|
uint16_t bl = readRegister8(MPR121_BASELINE_0 + t);
|
|
return (bl << 2);
|
|
}
|
|
|
|
/**
|
|
* @brief Read the touch status of all 13 channels as bit values in a 12 bit integer.
|
|
* @returns a 12 bit integer with each bit corresponding to the touch status
|
|
* of a sensor. For example, if bit 0 is set then channel 0 of the device is
|
|
* currently deemed to be touched.
|
|
*/
|
|
uint16_t Adafruit_MPR121::touched(void)
|
|
{
|
|
uint16_t t = readRegister16(MPR121_TOUCHSTATUS_L);
|
|
return t & 0x0FFF;
|
|
}
|
|
|
|
/*!
|
|
* @brief Read the contents of an 8 bit device register.
|
|
* @param reg the register address to read from
|
|
* @returns the 8 bit value that was read.
|
|
*/
|
|
uint8_t Adafruit_MPR121::readRegister8(uint8_t reg)
|
|
{
|
|
_wire->beginTransmission(_i2caddr);
|
|
_wire->write(reg);
|
|
_wire->endTransmission(false);
|
|
_wire->requestFrom(_i2caddr, 1);
|
|
if (_wire->available() < 1)
|
|
return 0;
|
|
return (_wire->read());
|
|
}
|
|
|
|
/*!
|
|
* @brief Read the contents of a 16 bit device register.
|
|
* @param reg the register address to read from
|
|
* @returns the 16 bit value that was read.
|
|
*/
|
|
uint16_t Adafruit_MPR121::readRegister16(uint8_t reg)
|
|
{
|
|
_wire->beginTransmission(_i2caddr);
|
|
_wire->write(reg);
|
|
_wire->endTransmission(false);
|
|
_wire->requestFrom(_i2caddr, 2);
|
|
if (_wire->available() < 2)
|
|
return 0;
|
|
uint16_t v = _wire->read();
|
|
v |= ((uint16_t)_wire->read()) << 8;
|
|
return v;
|
|
}
|
|
|
|
/*!
|
|
@brief Writes 8-bits to the specified destination register
|
|
@param reg the register address to write to
|
|
@param value the value to write
|
|
*/
|
|
void Adafruit_MPR121::writeRegister(uint8_t reg, uint8_t value)
|
|
{
|
|
//MPR121 must be put in Stop Mode to write to most registers
|
|
bool stop_required = true;
|
|
if (reg == MPR121_ECR || (0x73 <= reg && reg <= 0x7A)) {
|
|
stop_required = false;
|
|
}
|
|
if (stop_required) {
|
|
_wire->beginTransmission(_i2caddr);
|
|
_wire->write(MPR121_ECR);
|
|
_wire->write(0x00);
|
|
_wire->endTransmission();
|
|
}
|
|
|
|
_wire->beginTransmission(_i2caddr);
|
|
_wire->write((uint8_t)reg);
|
|
_wire->write((uint8_t)(value));
|
|
_wire->endTransmission();
|
|
|
|
if (stop_required) {
|
|
_wire->beginTransmission(_i2caddr);
|
|
_wire->write(MPR121_ECR);
|
|
_wire->write(0x8F);
|
|
_wire->endTransmission();
|
|
}
|
|
}
|